Advantix pipe lead-in R 120
Product information
Advantix pipe lead-in R 120
for polypropylene pipe and connected water seal odour trap
| Year built (from): | 1.1.2005 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe and are provided as a support feature.
Regulations from section: Application areas
Regulations from section: Media
Product description
Overview
- 1 Advantix pipe lead-in R 120
- 2 rockwool
- 3 Drainpipe, non-flammable
Technical data
Nominal width [DN] |
|---|
Material (pipe) |
Operating mode
Principle
In the case of fire, a conventional drain and a drainpipe made of plastic will melt and drip away within just a few minutes. Then there is an opening between two storeys, through which fire can spread.
The fire protection pipe lead-in can resist fire for up to 120 minutes, without fire and smoke spreading through the ceiling. Because the fire protection element contains a mass, which swells up at 150 °C and closes the empty areas in the lead-in completely.
The mounting brackets hold the fire protection pipe lead-in in the ceiling, even if the lower part of the casting compound breaks away.
Time elapsed
After 4 minutes
approx. 460 °C: The plastic pipe is becoming malleable.
After 8 minutes
approx. 625 °C: The plastic pipe is melted. The mass begins to swell and to fill the entire drill hole.
After 25 minutes
approx. 800 °C: Drill hole and connection are completely closed. The water trap remains largely in tact.
Information for use
Installation variations
The pipe lead-in can be mounted in the following way:
in a floor recess
in a drill hole
NOTICE!
The creation of a floor recess must be agreed with the following people:
a structural engineer
the on-site fire protection inspector or the specialist engineer for fire protection
If necessary, proof of compliance with building code or an expert's report must exist.
Handling
Assembly information
Important note
Assembly with small floor thickness
The pipe lead-in can be employed in floors at least 100 mm thick through drill holes, if the total floors thickness including bonding screed or floor installation panels is at least 150 mm.
Thinner floor thicknesses can be increased to a thickness of 150 mm by adding mortar strengthened with non-combustible floor installation panel (e. g. made of calcium silicate).
Notes on the use of floor installation panels
Mounting is allowed on or under the floor. Fastening must be carried out using end-to-end threaded rods ≥ M8.
If floor installation panels or concrete bases are to be used to reach the required fire resistance class, they must be at least 100 mm around the drill hole and laid at least 30 mm thick.
Installation dimensions
Tools and materials
Special tools
For drill hole:
Drill with drilling bit ∅ 100–122 mm
Material
For floor openings:
control panel or similar for closing the floor opening from belowEmpty pipe made of plastic, d 110
Mortar (MG II, IIa or III)
Assembly
Mounting the drain
The model can be installed in a ceiling recess or a drill hole.
Installation in a ceiling recess
-
Create the floor opening.
a = approx. 150 mm
-
Close the floor opening from below (e.g. with a switch panel).
-
Place a plastic pipe in the middle of the recess.
a = d 110
-
Ensure that the upper edge of the empty pipe closes flush with the upper edge of the floor.
-
Fasten the empty pipe.
-
Encase the empty pipe up to the upper edge with MG II, IIa or III and allow to set.
-
Remove the casing after hardening.
Installation in drill hole
-
Create the drill hole.
a = d 100–122
Mounting pipe lead-in
-
Remove the box.
-
Bend the bracket depending on the floor thickness.
-
Apply the lubricant to the seal ring and in the floor opening/drill hole.
-
Insert the pipe lead-in.
-
Push the drainpipe (3) supplied up to the middle of the coupling (4) into the pipe lead-in.
-
Extend with a second pipe (1) up to the upper edge of the floor.
-
Close the hollow space (2) with mineral fibre wool or mortar.
-
NOTICE!
A suitable adapter must be used to connect to a pipe made of cast iron.
Connect pipe end to the wastewater pipe.
-
Fill in and attach the sticker supplied.
-
The pipe lead-in has been mounted.
NOTICE!
The odour trap in the connected drain must be fully filled with water. Only then is the flawless functioning in case of fire guaranteed.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.
Disposal after fire
If fire protection material is involved in a fire, there may be residues which need to be specially treated. After a fire, secure the services of a company specialising in disposal of fire-damaged materials.