Urinal module
Product information
Urinal module
for urinal, connection of infrared electronics and inlet fittings of different makes
| Year built (from): | 10.3.1998 |
Trade mark rights exist for this document, further information can be found at viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-Fachkräfte
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
INFO!
Notes give you additional helpful tips.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Regulations from section: Sound protection
Product description
Overview
- 1 - connection for an inlet fitting
- 2 - threaded bolt
- 3 - mounting bracket for drain elbow
- 4 - drain elbow
Compatible components
Compatible flush plates
Sound protection
The urinal module complies with the noise insulation requirements specified in section Regulations from section: Sound protection .
Technical data
The product has the following technical data:
drain elbow |
|---|
Maximum height of urinal inlet from upper edge of the finished floor |
Handling
Assembly
Mounting module
Mounting in Steptec
INFO!
The two vertical rails, which surround the module, must be open towards the module and be at an interval of 430 mm.
Securing module
-
Secure the module onto the open Steptec rail with the slot nuts supplied:
-
Insert the slot nut into the opening of the module.
-
Push the slot nut in slightly.
-
Turn by 90°.
-
The slot nut is secured in the Steptec rail.
-
Align the height of the module.
-
Tighten the slot nut with a ring spanner (SW 17).
-
Tighten the other slot nuts in the same way.
-
The module is secured on the rail framework.
-
Lock the drainpipe in place in the holding device.
-
Close the bow around the drainpipe.
-
Set desired height for the bracket of the drain elbow (X). When doing so, observe the upper edge of the finished floor.
-
Attach bracket for threaded bolts:
Insert bracket horizontally and turn clockwise by 90°.
The distance between the brackets may only be a maximum of 390 mm.
-
Screw in threaded bolt and tighten with a ring spanner (SW 17).
-
Attach inlet fitting with the slot nuts.
-
Make water connection.
-
Make the electrical connection depending on the inlet fitting.
DANGER!Danger due to electrical current
An electric shock can lead to burns and serious injury and even death.
Work on the electrics may only be carried out by trained electricians.
Always de-energise the connection line before work is commenced.
-
Check height and width settings.
In addition, observe the instructions of the ceramic manufacturer.
Rounding off jobs
-
Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide Aqua-KS cladding panels.
When doing so, make sure that no abutting edges converge.
-
Grout the abutting edges and joints with a suitable filler.
-
Observe the instruction manual for the cladding panels for more information.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.